|
 VCU series controller uses 4 channels RC system to control R/C tank's forward/backward movement, sharp turning, pivoting, turret rotation and gun barrel evaluation at variable speed.
Plug-and-Play design for upgrading HL 1/16 RC Tank.
20A track motor driver.
22KHz, 8-bit high quality sound with digital sound mixer.
Maximum of 5 channel of sound track, main gun, machine gun, turret rotate, gun barrel elevation and engine sound can be generated at the same time.
3W sound output power.
Support air-soft gun with sound synchronization.
Support TAMIYA and HL IR battle unit and format.
Support RealEngine function.
Support RealRecoil servo port.
Safety shutoff prevents unwanted movement while signal lost.
Auto R/C signal detection.
|
|
VCU |
|
Remote Control Syste |
4-CH AM, FM or 2.4G |
|
TAMIYA IR battle |
YES |
Heng-Long IR battle |
YES |
|
Engine Sound rendering |
Frequency shift mode( Like el-mod) |
|
RealEngine( Patent Pending) |
NO |
|
Track driver |
20A |
|
Turret Rotation Speed Control |
YES |
Gun Elevation Speed Control |
YES |
|
Gun Elevation Servo Port |
NO |
AirSoft with Sound Synchronization |
YES |
|
RealRecoil
( Patent Pending) |
YES |
|
Smoker driver |
YES |
|
Head Light switch sound |
YES |
|
Head Light on/off control |
YES |
|
Tank Personalization |
YES |
elease Schedule |
2012/8/31 |
|
Part Number
|
Description
|
|
| SONY TV REMOTE |
For Tank Personalization, we can help to buy from local TV Store. |
Per order
|
|
Switch cable |
Switch + 30cm cable to connect to SW connector on MCU, not required for Heng-Long Tank
|
Per order |
|
IR LED Cable |
5mm IR LED + 30cm cable to connect to J1
|
Per order |
|
TBU Apple |
Base and cable to connect MCU board to TAMIYA Battle Unit.
|
Per order |
|
Control Mode and operation
|
 |
Engine sound on/off |
|
|
|
Cannon elevation |
|
|
|
Booming Cannon |
|
|
 |
Fire MG |
|
 |
Head light control on/off |
|
 |
Tank move forward and backward |
|
 |
Right and Left turn |
|
|
 |
Turret rotation |
|
|
Part Number |
Parameter
|
Value |
Unit |
|
VCU E66013/VCU E66023/VCU E66083/VCU E66143/VCU E66043/VCU E66053
|
Maximum current of track ESC |
20 |
A |
|
Maximum current of turret and cannon elevation ESC
|
7 |
A |
|
Maximum supply voltage |
7.4 |
V |
|
Minimum supply voltage |
7.2 |
V |
Inspect metal portion on FETs and make sure they are not touched to each other after shipment.
Disconnect RX-18 and plug cables to the same connector on TKs,.
Set Sound Volume to middle
Connect a switch to Switch Cable Port, just to short 2 pins in SW port if you are using HL tank.
,
Connect a recoil servo to J2,
Set CH1, 2 and 3 trimmer on transmitter to center position, Set CH4 trimmer on transmitter to most left or right position,
Power on MCU board and transmitter, you should hear turret traverse sound. if not, please contact us.
gently move CH4(Multi function control signal 2) trimmer to center till turret traverse is gone.
gently move CH2(Throttle ) trimmer up and down if you hear motor hum sound.
Cannon firing sound should be generated and recoil servo should moves when move CH3 stick to most top position, if not, gently move CH3(Multi function control signal 2 ) trimmer up and down till it work correctly.
You are all set.
|
